15:24
There are methods which you have to remember when you are installing new items. You have to follow it so that you would be able to install the Profile Design Cobra bars correctly. It is also required under the policy of the warranty that they would be giving to you. If you do not know how to do it, you should visit the dealer in your area.
You would be provided with a manual that indicates the procedures you must follow. If you prefer to get it done yourself, the tools that will be utilized on that must be prepared. An Allen or a torque wrench should be prepared. You will be needing a sandpaper since that will be utilized in making the parts smooth. When you got all of those tools, you may begin on this.
You should avoid greasing the clamping area. If you would be greasing it, it would only cause the bar to slip from it. You have to make sure that such situation would not happen especially when you are already using your bike. It would cause you to lose control while you are riding the bike. It would be very dangerous on your part if that would happen.
You have to make sure that the diameter of the bar clamp would match to the diameter of its stem. This should be checked so that you could avoid any problems with it. It would not fit if their diameter would not be the same. Before you would buy, you have to check the diameter so you would not waste your money on buying one.
If you are installing the stem that is new, there are still some instructions from the manufacturer that you should read. Some steps have been set by a manufacturer so you can be certain that it is correctly done. It is indicated on their manual so they can provide that on you so you will not find it difficult on how you can start with that.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You should slide the lever to the bar. If it makes you uncomfortable, you should adjust it depending on what you want. You have to place it carefully. You have to remember that if it would be broken, it would affect the warranty of the material.
It can be wrap if you prefer that. When you try this, you must ensure that a helmet would be worn. Inspect if it will function properly prior to the time you will be utilizing it on longer distances.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
You would be provided with a manual that indicates the procedures you must follow. If you prefer to get it done yourself, the tools that will be utilized on that must be prepared. An Allen or a torque wrench should be prepared. You will be needing a sandpaper since that will be utilized in making the parts smooth. When you got all of those tools, you may begin on this.
You should avoid greasing the clamping area. If you would be greasing it, it would only cause the bar to slip from it. You have to make sure that such situation would not happen especially when you are already using your bike. It would cause you to lose control while you are riding the bike. It would be very dangerous on your part if that would happen.
You have to make sure that the diameter of the bar clamp would match to the diameter of its stem. This should be checked so that you could avoid any problems with it. It would not fit if their diameter would not be the same. Before you would buy, you have to check the diameter so you would not waste your money on buying one.
If you are installing the stem that is new, there are still some instructions from the manufacturer that you should read. Some steps have been set by a manufacturer so you can be certain that it is correctly done. It is indicated on their manual so they can provide that on you so you will not find it difficult on how you can start with that.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You should slide the lever to the bar. If it makes you uncomfortable, you should adjust it depending on what you want. You have to place it carefully. You have to remember that if it would be broken, it would affect the warranty of the material.
It can be wrap if you prefer that. When you try this, you must ensure that a helmet would be worn. Inspect if it will function properly prior to the time you will be utilizing it on longer distances.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
About the Author:
When you are looking for information about Profile Design Cobra Bars go to the web pages online here today. You can see details at http://www.sportfactoryproshop.com now.
0 comments:
Post a Comment